Servo's, Switches, Extensions
Toward Pro MG996R Digital Servo
MG996R weight- 55.0g
Full Metal Geared, Digital
Dimension 40.7x19.7x42.9mm
Stall torque 9.4kg/cm (4.8V),11kg/cm (6V)
Operating speed 0.17sec/60degree (4.8v), 0.14sec/60degree (6v)
Operating voltage 4.8-7.2V
Temperature range 0℃_ 55℃
Dead band width 5us
This is essentially an upgraded version of the Tower Pro MG995 servo.
It now has a redesigned PCB and IC control system which makes it far more accurate.
Its internal gearing and motor are also upgraded to improve deadband width and centering.
This servo is far more accurate, and safe to use in aircraft which require precise movements and centering
$16 ea. with free postage
Servo Extensions
All extensions are heavy duty 22 AWG twisted wire fitted with J/R-Futaba leads
Free postage within Australia
150mm extension $3.50
300mm extension $3.70
450mm extension $3.90
600mm extension $4.10
900mm extension $5
1.2M Extension $5.75
150mm Y lead $3.60
300mm Y lead $4.10
600mm Y lead $5.30
Heavy duty Rx Switch with charge jack and green LED. JR connectors $9
Servo safety clips. These are a must have safety item. Every servo extension and Y lead should be made secure with these clips.
$6 for a pack of 10 clips,
Free post
Toward Pro MG958 Digital Coreless
Blue aluminium center case, heatsink
Full metal geared, no plastic
Weight- 65.0g
Dimension 40.7x19.7x42.9mm
Stall torque 12kg/cm (4.8V),14kg/cm (6V)
Operating speed 0.19sec/60degree (4.8v), 0.17sec/60degree (6V)
Operating voltage 4.8-7.2V
Temperature range 0℃_ 55℃
Dead band width 5us
Coreless motor
Dual ball bearings
This servo is far more accurate, and safe to use in aircraft which require precise movements and centering
Arms and mounting hardware included
$21 with free postage
Servo reversing Y lead. JR connectors
This is a must have item for connecting 2 servo's where one servo needs to be reversed. Such as in dual elevator servo fitments. It also has end point adjustment on one servo so you can exactly match the travel. Heavy duty leads.
Dionysus Design Servo Reverser. Made in the USA
# Accurately reverses the servo signal so the servo turns in the opposite direction.
# Over 800 steps of signal input/output resolution .
# Weight: 1 gram
# Size: 8mm x 44mm x 5mm (average)
# Power consumption: 4 mA
# Signal Range: 500us to 2500us
SP 3A 5v Switching BEC
Compact switching BEC
5-23v
2-5S Lipoly, 5-15 Cell Nicad or Nimh
11.5 gms including ferrite ring
Output 5v 3A continous
This is an excellent voltage regulator for use on petrol ignition when using Lipoly batteries.
$5
Body is CNC machined aluminium. Switch is a heavy duty toggle switch. Charge port. Inbuilt fuel dot. These are a very heavy duty switch.
Wires are 22AWG. Capacity 20A for 10 minutes
Twin Power switch. Can be used as a redundant switch or one for Rx and the other for the engine CDI. Two power inputs and two power outlets. Two charge ports. Heavy duty toggle switches. Body is CNC machined aluminium. 22AWG wires
Twin Power switch with fuel dot. Can be used as a redundant switch or one for Rx and the other for the engine CDI. Two power inputs and two power outlets. Two charge ports. Heavy duty toggle switches. Body is CNC machined aluminium. 22AWG wires. Capacity 20A for 10 minutes
Beware of the cheap copies with the shiny black case
Servo Reversing Lead Reverses the direction of a servo. It has an adjustable pot for setting the centre
JR/Futaba leads
Dionysus Design Servo Rate Reducer
This servo rate reducer is designed for airplanes where minimal weight is crucial. It uses the latest microprocessor technology to slow down the servo signal so landing gear and other mechanical systems are not damaged by fast servos.
Features:
• Slows down the servo signal so full range movement takes 4 seconds
• Designed for use with 2 or 3 position transmitter switches
• Can be used with 2 servos by using a Y-cable (if one of the two servos needs to be reversed we also recommend the use of a Servo Reverser)
We recommend using either blue Loctite or a smear of Silastic on the center arm screw. This is most important when using either 4 stroke or petrol engines.
This is recommended for all servo's with a metal output shaft.
